压力表使用一段时间,但压力不稳定,或压力表被删除,有时我们会发现指针的指针原来剑已成为弯刀的形状,如果你仔细看,在“背”,会留下一点凹痕或抑郁大小明显,指针是弯曲的。 yā压 lì力 biǎo表 shǐ使 yòng用 yī一 duàn段 shí时 jiān间 , dàn但 yā压 lì力 bù不 wěn稳 dìng定 , huò或 yā压 lì力 biǎo表 bèi被 shān删 chú除 , yǒu有 shí时 wǒ我 men们 huì会 fā发 xiàn现 zhǐ指 zhēn针 de的 zhǐ指 zhēn针 yuán原 lái来 jiàn剑 yǐ已 chéng成 wéi为 wān弯 dāo刀 de的 xíng形 zhuàng状 , rú如 guǒ果 nǐ你 zǐ仔 xì细 kàn看 , zài在 “ bèi背 ” , huì会 liú留 xià下 yī一 diǎn点 āo凹 hén痕 huò或 yì抑 yù郁 dà大 xiǎo小 míng明 xiǎn显 , zhǐ指 zhēn针 shì是 wān弯 qū曲 de的 。
Bending pressure gauge pressure gauge pointer, a relative check nails, "the" bent down, this is because the pressure gauge at work when the pressure relief is too fast, too fast, so that the pointer violently and repeatedly hit the nail plate check. This is generally in the lower side of the pressure gauge pointer, pointer and check the location of the contact pin, can be seen by the impact of severe impact, traces of this site will leave the gap depth.
弯曲压力表压力表指针,一个相对的检查钉,“”弯曲,这是因为压力表在工作时,压力太快,太快,使指针猛烈,反复打钉板检查。这一般在压力表指针的下方,指针和接触销的位置检查,可以看出受严重冲击的影响,这个部位的痕迹会留有间隙深度。
wān弯 qū曲 yā压 lì力 biǎo表 yā压 lì力 biǎo表 zhǐ指 zhēn针 , yī一 gè个 xiāng相 duì对 de的 jiǎn检 chá查 dīng钉 , “ ” wān弯 qū曲 , zhè这 shì是 yīn因 wèi为 yā压 lì力 biǎo表 zài在 gōng工 zuò作 shí时 , yā压 lì力 tài太 kuài快 , tài太 kuài快 , shǐ使 zhǐ指 zhēn针 měng猛 liè烈 , fǎn反 fù复 dǎ打 dīng钉 bǎn板 jiǎn检 chá查 。 zhè这 yī一 bān般 zài在 yā压 lì力 biǎo表 zhǐ指 zhēn针 de的 xià下 fāng方 , zhǐ指 zhēn针 hé和 jiē接 chù触 xiāo销 de的 wèi位 zhi置 jiǎn检 chá查 , kě可 yǐ以 kàn看 chū出 shòu受 yán严 zhòng重 chōng冲 jī击 de的 yǐng影 xiǎng响 , zhè这 ge个 bù部 wèi位 de的 hén痕 jì迹 huì会 liú留 yǒu有 jiàn间 xì隙 shēn深 dù度 。
There is a relative pressure check dial "back" to the curved nail. This is because the pressure gauge is used, pressure is too large, too fast to the pressure gauge pointer clockwise disc check and nail bending impact. The same will leave a gap in the upper side of the pressure gauge pointer.
有一个相对压力检查拨号“回”的弯曲的指甲。这是因为压力表是用的,压力过大,过快到压力表指针的顺时针圆盘止回阀和指甲弯曲的影响。相同的将在压力表指针的上侧面留下一个间隙。
yǒu有 yī一 gè个 xiāng相 duì对 yā压 lì力 jiǎn检 chá查 bō拨 hào号 “ huí回 ” de的 wān弯 qū曲 de的 zhǐ指 jia甲 。 zhè这 shì是 yīn因 wèi为 yā压 lì力 biǎo表 shì是 yòng用 de的 , yā压 lì力 guò过 dà大 , guò过 kuài快 dào到 yā压 lì力 biǎo表 zhǐ指 zhēn针 de的 shùn顺 shí时 zhēn针 yuán圆 pán盘 zhǐ止 huí回 fá阀 hé和 zhǐ指 jia甲 wān弯 qǔ曲 de的 yǐng影 xiǎng响 。 xiāng相 tóng同 de的 jiāng将 zài在 yā压 lì力 biǎo表 zhǐ指 zhēn针 de的 shàng上 cè侧 miàn面 liú留 xià下 yī一 gè个 jiàn间 xì隙 。
The gauge pressure of the material is generally Aluminum Alloy plate, if the pressure gauge pointer material is too thin, the material is too soft, the reason is also the pressure gauge pointer easily bending.
材料的表压力一般是铝合金板,如果压力表指针材料太薄,材料太软,原因是压力表指针也容易弯曲。